DC Audio 3.5k - 3,500w Monoblock Amplifier
Review: 5 - "A masterpiece of literature" by , written on May 4, 2006
I really enjoyed this book. It captures the essential challenge people face as they try make sense of their lives and grow to adulthood.

DC Audio 3.5k - 3,500w Monoblock Amplifier

Available: In Stock
  • Product SKU: G2D3691E
$10,999.99
Snap Logo Lease for as low as $/week Learn More
Image

The 3.5kw competition series amplifier is a 3,500 watt mono block. It is capable of running up to 18 volts

for up to 5,100 watts. It is a linkable amp and designed to run a 1 ohm per amp or 2 ohms when strapped.
It comes with a bass knob and a clipping indicator. For power inputs it will accept 0 awg for power and
0 awg for ground.

 

Key Features
• 1 ohm stable
• Variable low pass filter
• Variable subsonic filter
• Variable bass boost
• Wired remote control
• Clipping indicator

We recommend for installation
• 1 upgraded battery under the hood
• 1 extra battery in the rear
• Minimum of one 0 awg ran from the front battery to the rear battery
• Upgraded aftermarket alternator
• Dash mounted voltage meter

  Features Voltage 3.5kw
Output Power (RMS) 4 ohm 14.4V 750W x 1
2 ohm 1,800W x 1
1 ohm 3,500W x 1
1 ohm 16V 4,000W x 1
1 ohm 18V 5,100Wx1
Input Sensitivity     6V~0.2V
Low Pass Filter Switchable    
( @ 24 dB Slope) Variable Hz 35~250
Subsonic Filter Switchable    
( @ 24dB slope ) Variable Hz 10~50
Bass Boost Variable dB 0-9dB
Frequency Response   Hz 15-270
Signal to Noise Ratio   dB 100
Damping factor     150<
Efficiency @ 4ohm   % Over 90%
THD @ 4ohms     Less than 0.1%
Fuse Rating     300 Amps
Linked Fuse Rating     600 Amps
Indicator Power   Yes
Protection   Yes
Clip   Yes
Speaker & Power terminal Mold Type    Yes
Power Gauge 0Ga
Heatsink Length inch/mm   21.26"/540mm
Heatsink Width inch/mm   9.38"/238mm
Heatsink Height inch/mm   2.35"/59.6mm

The 3.5kw competition series amplifier is a 3,500 watt mono block. It is capable of running up to 18 volts

for up to 5,100 watts. It is a linkable amp and designed to run a 1 ohm per amp or 2 ohms when strapped.
It comes with a bass knob and a clipping indicator. For power inputs it will accept 0 awg for power and
0 awg for ground.

 

Key Features
• 1 ohm stable
• Variable low pass filter
• Variable subsonic filter
• Variable bass boost
• Wired remote control
• Clipping indicator

We recommend for installation
• 1 upgraded battery under the hood
• 1 extra battery in the rear
• Minimum of one 0 awg ran from the front battery to the rear battery
• Upgraded aftermarket alternator
• Dash mounted voltage meter

  Features Voltage 3.5kw
Output Power (RMS) 4 ohm 14.4V 750W x 1
2 ohm 1,800W x 1
1 ohm 3,500W x 1
1 ohm 16V 4,000W x 1
1 ohm 18V 5,100Wx1
Input Sensitivity     6V~0.2V
Low Pass Filter Switchable    
( @ 24 dB Slope) Variable Hz 35~250
Subsonic Filter Switchable    
( @ 24dB slope ) Variable Hz 10~50
Bass Boost Variable dB 0-9dB
Frequency Response   Hz 15-270
Signal to Noise Ratio   dB 100
Damping factor     150<
Efficiency @ 4ohm   % Over 90%
THD @ 4ohms     Less than 0.1%
Fuse Rating     300 Amps
Linked Fuse Rating     600 Amps
Indicator Power   Yes
Protection   Yes
Clip   Yes
Speaker & Power terminal Mold Type    Yes
Power Gauge 0Ga
Heatsink Length inch/mm   21.26"/540mm
Heatsink Width inch/mm   9.38"/238mm
Heatsink Height inch/mm   2.35"/59.6mm